Posts Tagged 'truck'

hobbAD – Wooly Bullies 2013 raffle bike

thanks bully buddies, i’ll get around to it sooner or later!

IMG_20130923_094112

IMG_0847

IMG_0848

IMG_0849

IMG_0850

IMG_0851

IMG_0852

IMG_0853

IMG_0854

IMG_0856

IMG_0857

quick truck update

new distributor cap, rotor and plug wires and the truck is running so much better! just a bit more work here and there and it should be la ready.
IMG_6688

ciao update later!

new shocks for the truck

last weekend i spent a couple hours playing with the truck. as i said last time, it burns a little oil (and leaks a bit too – as in quite a bit), so after verifying the pcv valve was ok (a bad one can cause your engine to suck oil from the under the valve cover and dump it into the intake, giving you smokey exhaust and requiring frequent oil top-offs), i figure it’s probably bad rings on one or more of the pistons.
IMG_0729

IMG_0734
i ran a compression test on all six cylinders and i got quite a spread of numbers in the results; they range from 145psi to 170psi.
however, after doing some homework it would seem that i might be alright there. my reading tells that all cylinders should be within 15% of one another. i coulda sworn it was 20%, at least that’s what i remember from back in my bmw days, but i’m going with what the internet says. internet’s always right.
anyway, 170 x .15 = 25.5 (26 rounded off). 170 – 26 = 144, so my lowest cylinder just cuts it by the skin of it’s teeth (pistons have teeth, btw).
my next lowest reading was 152psi, then 158psi, 168 and two at 170. while having one cylinder just 1psi away from not making the grade is not ideal, it’ll do for now. once i get back from la i’ll plan on doing the rings.

however, it seems like rings probably aren’t my oil consumption problem, which more or less leaves valve guides. they are pretty easy to do on this engine, and with the right tools can be done in like an hour or two without removing the head from the engine. i’m going to buy the tools and plan on doing that before la, but depending on time and such it might have to wait also. i did pick up a case of 10w-30 at costco, so maybe i’ll just bring it along and top up as needed!

i replaced the plugs while i was at it. there were three different types of plugs in the thing, only two being the proper type. oh well, they are all proper now!

IMG_0731
see that thing hanging under my dash near the driver door there? kinda what from this angle appears to be right next to the clutch pedal? that’s my ignition switch. i should probably get that taken care of before the trip too, but it’s not a priority at the moment. also, yes, that is the same seat cover that every other old truck ever has.

an issue i discovered when driving home from reno was that both the front shocks were completely blown. L was following me in her scion and said that at times the the front wheels would dribble down the freeway like a basketball. shocks were like $35 for the pair, so i busted that out real quick.
here’s the passenger side shock next to the new one. the old shocks had less resistance than a toy accordion, and since everyone everywhere has a toy accordion i assume you all know what i mean.
IMG_0740

driverside old –
IMG_0742

driverside new –
IMG_0743

the radius arm bushings need replace super bad too, but i’m not sure if that’ll get done before la or not.
IMG_0735

the rear shocks seem fine, but i’ll probably replace them anyway since they are so cheap.
IMG_0739
i’ve got a 4.10 dana 60 full floating rear end, great for towing and hauling anything but ass. it’s not a fast truck, but i didn’t want a fast truck. i can’t drive 55! no, really. ok, i do 65 comfortably, maybe 70 if i feel like burning money.

the hood hinges are pretty blown out. the springs are fine, but all the pivot points are sloppy and the hood hangs about a foot lower than it should when up, i have an ever-healing cut on my head from constantly running into the hood latch. i’m going to change those soon.

some pictures-
IMG_0730

IMG_0733

IMG_0737

IMG_0736

IMG_0732

that’s my truck! i took it for a spin to run some errands once i was done and replacing the front shocks made it a whole new truck.
IMG_0744

alan and i are going to go hit up a couple pick-n-pulls this weekend and i’ve got a short shopping list of odds and ends i wanna pick up. namely those hood hinges. and maybe a tail light lens. and a non-mix-matched set of plug wires. and possibly a set of rear shocks if i see some that look newish. and a steelie spare wheel with a good tire. and and and an dn adnadn adna dna dnadn adnadn

new toy – 1968 ford f250

i’ve been looking for a truck for a while now, and talking about how i needed one even longer. after selling the ninja earlier this month, i was finally in the position to do something.
my criteria was that it had to be 1975 or older (ca smog exempt), two wheel drive, six cylinder and manual. shortbed would have been nice for parking in sf, but that alone would quadruple the price on most trucks, so i wasn’t holding out for one. besides, i knew i’d be happier with a long bed even if it is going to be a bitch to park sometimes.
i had a lead on a 68 f100 short bed in reno, my friend and fellow los dorados member troy was also looking for a truck, so i took a bus over the pass and we went truck shopping.
that f100 ended up being a bust, i had heard about it from don sumpter (who is the latest member of los dorados) – the truck belonged to his neighbor’s coworker’s mother-in-law or something to that effect. apparently the old lady’s husband died a while back and left a couple trucks behind and she wanted them gone. unfortunately, don had no direct line to her and i never got to see the dumb thing.
don was also selling his truck, a 79 ford f150. it was too new and the 6cyl and 4 speed had been replaced with a 352 v8 automatic lump, so i knew it wasn’t for me – though it is a super awesome truck. troy ended up picking it up cheap and is really happy with it, even if he is a little embarrassed by the political commentary on the tailgate.

i was extremely jealous and it really got me pumped to find a truck of my own, i was emailing people with trucks on craigslist from washington state down to southern california. people were getting mad at me because i couldn’t remember which truck they were selling. was that the 72 dodge or the 74 ford?
i finally found what i was looking for. a clean looking 68 f250 on reno craigslist. 300 4.9l inline six with four on the floor. it was sitting over in sparks, the pictures were pretty bad but i could tell it wasn’t super rough (some of the trucks i was looking at were pretty bad).


it was priced about what i was looking to pay at $800 (it was up for $1000 previously, but i had my filter set at $850 so i missed it), so i decided to go for it.
i texted with the guy and he said the first person to show up with $600 can take it. this was a wednesday and i was at work, i texted L to see if she wanted to go to reno for dinner.
we drove to reno after i got off work and by time we got to the place, it was getting dark. the truck looked awesome, though the battery was dead and the guy couldn’t get the truck started.
after a couple hours of messing with it and a new battery, the dude offered me the truck for $500 (what he paid for it, he says) and swears it runs great, he just had it running three days ago.
the whole time i’m telling the guy it’s a bad connection at the battery, so after i agree to take it for $500, i grab his pliers and take apart the hot wire battery terminal and scrape the corrosion out of it and cut the wire back past the corroded part, put it back together and started it up on the first crank.
i drove it up and down his street with a flat front tire (not having power steering it was a bitch) and was in love with it. we exchanged papers and i told him i’d be back on saturday to pick it up.
that saturday L and i drove back to reno and stayed at troy’s. we went to the pick-n-pull and got a new seat for his f150 and some stock steel ford 8 lug wheels for my truck. i hated the chrome chrysler wheels that were on there and it needed tires no matter what, so i figured i’d spend $40 on proper wheels and put tires on those instead. and that’s what i did.
after putting tires on the truck, i took it to troys and crawled around under it for a good hour or so rigging up the brake and tail lights. this thing’s going to need to be completely rewired someday, but it’s good enough for now.
new wheels and tires on, tail and brake lights now working, it was time to head back to sacramento.


the drive went pretty well, though the front shocks were so blown that at random times the wheels would start dribbling down the freeway. i also noticed that oil pressure was getting pretty low, so i stopped and ended up putting three quarts of oil in it. it smokes a bit and is weeping around the oil pan and lifter cover, so it definitely needs some work, but i couldn’t be more happy with it.
i am planning on driving it down to la for the bullies rally at the end of next month, so i have some work to do before then. i’ll have doug and probably troy along with me, it should be pretty exciting!
i hope we make it!


enter your email address to follow this blog and receive notifications of new posts by email.

Join 120 other followers

or pick a category!

furniture moped moto nuffin scooter truck van

  • 19,244 yous guys